Superwinch 1181 Manuale delle Istruzioni Scaricare il pdf (Pagina 2)

Thank you very much for purchasing a Superwinch product. We hope and

expect that you will be pleased with the performance and reliability of this

unit. If you are not, for any reason, please contact our Customer Service

Department: (860) 928-7787 USA; (1822) 614101 England.

When requesting information or ordering replacement parts; always give the

following information:

1. Winch Part Number

2. Part Number (found in Replacement Parts List section)

3. Part Description

It is extremely important that you read and understand this Owner’s Manual

prior to installing and using your winch. Pay particular attention to “General

Safety Information” and be sure that anyone else who might use your winch

also studies this section.

Pay particular attention to the caution notes preceded

with this symbol. The notes contain advice for your

protection.

Description Quantity

Winch assembly with wire rope and hook installed 1

Switch and harness assembly with two 5' long 8-gauge wires 1

Handsaver 1

Circuit breaker assembly with hardware 1

Poly bag containing: 2 bolts, 2 washers, 2 nuts, 1

4 flat washers and 5 cable ties

INTRODUCTION

UNPACKING: This carton contains the following items. Please unpack care-

fully. Read instructions before beginning.

PERFORMANCE

Motor

Volt Load Speed Current

DC lbs kg Ft/min m/min Amps

12 0 0 25 7.6 30

2,000 907 9 2.7 200

24 0 0 25 7.6 20

2,000 907 9 2.7 100

Working Load . . . . . 2,000 lbs. (907 kg)

Stall Load . . . . . . . 2,500 lbs. (1,134 kg)

Wire Rope . . . . . . . . . 3/16” x 25 ft.

Voltage . . . . . . . . 12 or 24 Volt DC

Motor . . . . . . . . . . . . . . . . . .1.3 hp

Gear Ratio . . . . . . . . . . . . . . . 123:1

Weight . . . . . . . . . . 18 lbs. (8.2 kg)

SPECIFICATIONS

GENERAL SAFETY

INFORMATION

Your new Superwinch is a powerful

machine. Treat it with respect, use it

with caution and always follow

these safety guidelines.

1. The X1 winch is rated at 2,000

lbs. (single-line) capacity. DO NOT

OVERLOAD. DO NOT ATTEMPT

PROLONGED PULLS AT HEAVY

LOADS. DO NOT MAINTAIN

POWER TO THE WINCH IF THE

MOTOR STALLS. Overloads can

damage the winch and/or the

wire rope and create unsafe

operating conditions. FOR

HEAVY LOADS, WE RECOM-

MEND THE USE OF THE

OPTIONAL PULLEY BLOCK AND

HOOK ASSEMBLY (PART NO.

2227) TO DOUBLE-LINE THE

WIRE ROPE (Figure 1). This

reduces the load on the winch

and the strain on the wire rope

by approximately 50%.

2. AFTER READING AND UNDER-

STANDING THIS MANUAL,

LEARN TO USE YOUR WINCH.

Practice using it so you will be

familiar with it when the need

arises. Periodically check the

winch installation to assure that

all bolts are tight.

3. DO NOT “move

”

your vehicle to

assist the winch in pulling a load.

The combination of the winch

and vehicle pulling together

could overload the wire rope and

the winch itself.

4. KEEP WINCHING AREA CLEAR.

Do not allow people to remain in

the area during winching opera-

tions. Do not step over a taut

wire rope or allow anyone else to

do so. Do not stand between the

winch and load.

5. INSPECT WIRE ROPE AND

EQUIPMENT FREQUENTLY. A

FRAYED WIRE ROPE WITH BRO-

KEN STRANDS SHOULD BE

REPLACED IMMEDIATELY.

Always replace wire rope

with the manufacturer’s iden-

tical replacement part, (see

Replacement Parts List). Never

replace the wire rope with any

kind of rope other than the type

and size specified in the Wire

Rope section of this manual.

6. USE HEAVY LEATHER GLOVES

when handling wire rope. DO

NOT LET WIRE ROPE SLIDE

THROUGH YOUR HANDS. A bro-

ken strand could seriously injure

your hands.

7. KEEP CLEAR OF THE WINCH,

WIRE ROPE, AND HOOK WHEN

OPERATING WINCH. NEVER put

your fingers through the hook

when reeling in the last few feet

of line. If your finger should

become trapped in the hook, you

could lose your finger. Use the

HAND SAVER BAR (Figure 2) to

guide the hook within the last

few feet. Never guide a wire rope

on or off the drum with your hand.

Figure 2

Slope* 10% (6º) 20% (11º) 30% (17º) 100% (45º)

Lbs.**

kg**

10,000

4535

6,800

3084

5,200

2359

2,600

1179

Ratings assume a 10% coefficient of friction.

* A 10% slope is a rise of one foot in ten feet. Slope in approximate degrees is also shown above.

** All loads shown are for single-line operation (see Figure 1). Double-line operation with optional

pulley block (P/N 2227) approximately doubles capacity of winch (see Figure 1).

ROLLING LOAD CAPACITY**

Figure 1

Single Line

Double Line

1 2 3 4 5 6 7 8

Commenti su questo manuale

Nessun commento

Superwinch 1181 Manuale delle Istruzioni Pagina 2

Commenti su questo manuale